feat(platform): adapt GPIO configuration to new board
This commit is contained in:
chenjintao
+298
-281
@@ -1,5 +1,302 @@
|
||||
menu "TQ Cat Configuration"
|
||||
|
||||
menu "Board Hardware Configuration (GPIO)"
|
||||
|
||||
comment "LCD"
|
||||
|
||||
config TQ_SCREEN_RESET_PIN
|
||||
int "Panel reset GPIO (-1 to disable hardware reset)"
|
||||
default 7
|
||||
range -1 48
|
||||
help
|
||||
The new upper board maps the ST7789P3 RES signal to IO7.
|
||||
Use -1 only when panel reset is physically not connected.
|
||||
|
||||
config TQ_SCREEN_SPI_MISO_GPIO
|
||||
int "LCD SPI MISO GPIO (-1 to disable)"
|
||||
default -1
|
||||
range -1 48
|
||||
help
|
||||
LCD SPI MISO GPIO. Use -1 when the panel does not connect MISO.
|
||||
|
||||
config TQ_SCREEN_SPI_MOSI_GPIO
|
||||
int "LCD SPI MOSI GPIO"
|
||||
default 15
|
||||
range 0 48
|
||||
help
|
||||
LCD SPI MOSI GPIO.
|
||||
|
||||
config TQ_SCREEN_SPI_CLK_GPIO
|
||||
int "LCD SPI clock GPIO"
|
||||
default 16
|
||||
range 0 48
|
||||
help
|
||||
LCD SPI clock GPIO.
|
||||
|
||||
config TQ_SCREEN_SPI_CS_GPIO
|
||||
int "LCD SPI CS GPIO"
|
||||
default 5
|
||||
range 0 48
|
||||
help
|
||||
LCD SPI chip-select GPIO.
|
||||
|
||||
config TQ_SCREEN_DC_GPIO
|
||||
int "LCD D/C GPIO"
|
||||
default 6
|
||||
range 0 48
|
||||
help
|
||||
LCD data/command GPIO.
|
||||
|
||||
config TQ_SCREEN_BACKLIGHT_GPIO
|
||||
int "LCD backlight GPIO"
|
||||
default 4
|
||||
range 0 48
|
||||
help
|
||||
LCD backlight control GPIO.
|
||||
|
||||
config TQ_SCREEN_BACKLIGHT_ACTIVE_HIGH
|
||||
bool "Backlight active high"
|
||||
default y
|
||||
|
||||
comment "Audio"
|
||||
|
||||
config MULTIMODAL_AUDIO_I2C_SCL_GPIO
|
||||
int "I2C SCL GPIO"
|
||||
default 2
|
||||
help
|
||||
Default from docs/gpio-map.md (ES8311 control SCL on GPIO2).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2C_SDA_GPIO
|
||||
int "I2C SDA GPIO"
|
||||
default 1
|
||||
help
|
||||
Default from docs/gpio-map.md (ES8311 control SDA on GPIO1).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_MCLK_GPIO
|
||||
int "I2S MCLK GPIO"
|
||||
default 38
|
||||
help
|
||||
Default from docs/gpio-map.md (I2S_MCLK on GPIO38).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_BCLK_GPIO
|
||||
int "I2S BCLK GPIO"
|
||||
default 39
|
||||
help
|
||||
Default from docs/gpio-map.md (I2S_SCLK on GPIO39).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_WS_GPIO
|
||||
int "I2S WS GPIO"
|
||||
default 41
|
||||
help
|
||||
Default from docs/gpio-map.md (I2S_LRCK on GPIO41).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_DOUT_GPIO
|
||||
int "I2S DOUT GPIO"
|
||||
default 40
|
||||
help
|
||||
Default from docs/gpio-map.md (MCU output to ES8311 DSDIN on GPIO40).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_DIN_GPIO
|
||||
int "I2S DIN GPIO"
|
||||
default 42
|
||||
help
|
||||
Default from docs/gpio-map.md (MCU input from ES8311 ASDOUT on GPIO42).
|
||||
|
||||
config MULTIMODAL_AUDIO_PA_GPIO
|
||||
int "PA enable GPIO (-1 to disable)"
|
||||
default 9
|
||||
help
|
||||
Default from docs/gpio-map.md (PA_CTRL on IO9).
|
||||
|
||||
comment "Buttons & Digital Inputs"
|
||||
|
||||
config MULTIMODAL_PTT_BUTTON_GPIO
|
||||
int "Push-to-talk button GPIO"
|
||||
default 13
|
||||
range 0 48
|
||||
help
|
||||
The new board routes the TTP223 touch output to GPIO13.
|
||||
Verify its idle/active levels on hardware before changing
|
||||
the active-level and pull-resistor settings.
|
||||
|
||||
config MULTIMODAL_PTT_BUTTON_ACTIVE_LEVEL
|
||||
int "Push-to-talk button active level"
|
||||
default 0
|
||||
range 0 1
|
||||
help
|
||||
Logic level that means the push-to-talk button is pressed.
|
||||
|
||||
config MULTIMODAL_PTT_BUTTON_PULLUP
|
||||
bool "Enable push-to-talk button pull-up"
|
||||
default y
|
||||
help
|
||||
Enable the internal pull-up when required by the button wiring.
|
||||
|
||||
config MULTIMODAL_PTT_BUTTON_PULLDOWN
|
||||
bool "Enable push-to-talk button pull-down"
|
||||
default n
|
||||
help
|
||||
Enable the internal pull-down when required by the button wiring.
|
||||
|
||||
config TQ_CALIBRATION_SWITCH_GPIO
|
||||
int "Direction calibration switch GPIO"
|
||||
default 11
|
||||
range 0 48
|
||||
help
|
||||
GPIO used for switch 1 on IO11 and for turntable
|
||||
direction calibration.
|
||||
|
||||
config TQ_CALIBRATION_SWITCH_ACTIVE_LEVEL
|
||||
int "Direction calibration switch active level"
|
||||
default 0
|
||||
range 0 1
|
||||
help
|
||||
Logic level that means the calibration switch is active.
|
||||
|
||||
config TQ_CALIBRATION_SWITCH_PULLUP
|
||||
bool "Enable direction calibration switch pull-up"
|
||||
default y
|
||||
help
|
||||
Enable the internal pull-up for the default active-low wiring.
|
||||
|
||||
config TQ_CALIBRATION_SWITCH_PULLDOWN
|
||||
bool "Enable direction calibration switch pull-down"
|
||||
default n
|
||||
help
|
||||
Leave disabled for the default active-low wiring.
|
||||
|
||||
config TQ_SLOT_SWITCH_GPIO
|
||||
int "Slot feature switch GPIO"
|
||||
default 12
|
||||
range 0 48
|
||||
help
|
||||
GPIO used by the input that triggers the slot machine feature.
|
||||
|
||||
config TQ_SLOT_SWITCH_ACTIVE_LEVEL
|
||||
int "Slot feature switch active level"
|
||||
default 0
|
||||
range 0 1
|
||||
help
|
||||
Logic level that means the slot machine feature switch is active.
|
||||
|
||||
config TQ_SLOT_SWITCH_PULLUP
|
||||
bool "Enable slot feature switch pull-up"
|
||||
default y
|
||||
help
|
||||
Enable the internal pull-up for the default active-low slot switch wiring.
|
||||
|
||||
config TQ_SLOT_SWITCH_PULLDOWN
|
||||
bool "Enable slot feature switch pull-down"
|
||||
default n
|
||||
help
|
||||
Leave disabled for the default active-low slot switch wiring.
|
||||
|
||||
config TQ_RESET_BUTTON_GPIO
|
||||
int "Wi-Fi reset button GPIO"
|
||||
default 14
|
||||
range 0 48
|
||||
depends on TQ_RESET_BUTTON_ENABLE
|
||||
help
|
||||
GPIO used for the dedicated Wi-Fi reset button when enabled.
|
||||
The new board uses GPIO14 for stepper IN1. Keep this feature
|
||||
disabled unless a separate reset input is physically wired
|
||||
and its GPIO configured without conflicts.
|
||||
|
||||
config TQ_RESET_BUTTON_ACTIVE_LEVEL
|
||||
int "Wi-Fi reset button active level"
|
||||
default 0
|
||||
range 0 1
|
||||
depends on TQ_RESET_BUTTON_ENABLE
|
||||
help
|
||||
Logic level that means the Wi-Fi reset button is pressed.
|
||||
|
||||
config TQ_RESET_BUTTON_PULLUP
|
||||
bool "Enable Wi-Fi reset button pull-up"
|
||||
default y
|
||||
depends on TQ_RESET_BUTTON_ENABLE
|
||||
help
|
||||
Enable the internal pull-up for active-low wiring.
|
||||
|
||||
config TQ_RESET_BUTTON_PULLDOWN
|
||||
bool "Enable Wi-Fi reset button pull-down"
|
||||
default n
|
||||
depends on TQ_RESET_BUTTON_ENABLE
|
||||
help
|
||||
Enable the internal pull-down for active-high wiring.
|
||||
|
||||
comment "Stepper Motor"
|
||||
|
||||
config TQ_STEPPER_IN1_GPIO
|
||||
int "Turntable stepper IN1 GPIO"
|
||||
default 14
|
||||
range 0 48
|
||||
help
|
||||
GPIO connected to the turntable stepper driver IN1 input.
|
||||
|
||||
config TQ_STEPPER_IN2_GPIO
|
||||
int "Turntable stepper IN2 GPIO"
|
||||
default 21
|
||||
range 0 48
|
||||
help
|
||||
GPIO connected to the turntable stepper driver IN2 input.
|
||||
|
||||
config TQ_STEPPER_IN3_GPIO
|
||||
int "Turntable stepper IN3 GPIO"
|
||||
default 47
|
||||
range 0 48
|
||||
help
|
||||
GPIO connected to the turntable stepper driver IN3 input.
|
||||
|
||||
config TQ_STEPPER_IN4_GPIO
|
||||
int "Turntable stepper IN4 GPIO"
|
||||
default 48
|
||||
range 0 48
|
||||
help
|
||||
GPIO connected to the turntable stepper driver IN4 input.
|
||||
|
||||
comment "Power & Battery"
|
||||
|
||||
config TQ_POWER_HOLD_GPIO
|
||||
int "Power hold GPIO (-1 to disable)"
|
||||
default -1
|
||||
range -1 48
|
||||
help
|
||||
GPIO used to keep board power enabled after boot. The new
|
||||
board has no MCU-controlled power-hold net; leave disabled.
|
||||
|
||||
config TQ_POWER_HOLD_ACTIVE_LEVEL
|
||||
int "Power hold active level"
|
||||
default 1
|
||||
range 0 1
|
||||
help
|
||||
Logic level that keeps the external power-hold circuit active.
|
||||
|
||||
config TQ_BATTERY_ADC_GPIO
|
||||
int "Battery voltage ADC GPIO"
|
||||
default 17
|
||||
range 0 48
|
||||
depends on TQ_BATTERY_ENABLE
|
||||
|
||||
config TQ_BATTERY_CHARGE_GPIO
|
||||
int "TP4056 charge status GPIO (-1 to disable)"
|
||||
default 18
|
||||
range -1 48
|
||||
depends on TQ_BATTERY_ENABLE
|
||||
|
||||
config TQ_BATTERY_CHARGE_ACTIVE_LEVEL
|
||||
int "TP4056 charging active level"
|
||||
default 0
|
||||
range 0 1
|
||||
depends on TQ_BATTERY_ENABLE
|
||||
|
||||
config TQ_BATTERY_SHUTDOWN_WAKE_BUTTON_GPIO
|
||||
int "Optional active-low deep-sleep wake button GPIO (-1 to disable)"
|
||||
default -1
|
||||
range -1 48
|
||||
depends on TQ_BATTERY_CONTROLLED_SHUTDOWN_ENABLE
|
||||
|
||||
endmenu
|
||||
|
||||
menu "Legacy LCD Driver Options"
|
||||
|
||||
choice LCD_TYPE
|
||||
@@ -549,37 +846,6 @@ menu "TQ Cat Configuration"
|
||||
configured duration clears saved Wi-Fi credentials and then
|
||||
restarts the device. Other persisted data is not changed.
|
||||
|
||||
config TQ_RESET_BUTTON_GPIO
|
||||
int "Wi-Fi reset button GPIO"
|
||||
default 14
|
||||
range 0 48
|
||||
depends on TQ_RESET_BUTTON_ENABLE
|
||||
help
|
||||
GPIO used for the dedicated Wi-Fi reset button when enabled.
|
||||
GPIO14 is unassigned on the current board revision.
|
||||
|
||||
config TQ_RESET_BUTTON_ACTIVE_LEVEL
|
||||
int "Wi-Fi reset button active level"
|
||||
default 0
|
||||
range 0 1
|
||||
depends on TQ_RESET_BUTTON_ENABLE
|
||||
help
|
||||
Logic level that means the Wi-Fi reset button is pressed.
|
||||
|
||||
config TQ_RESET_BUTTON_PULLUP
|
||||
bool "Enable Wi-Fi reset button pull-up"
|
||||
default y
|
||||
depends on TQ_RESET_BUTTON_ENABLE
|
||||
help
|
||||
Enable the internal pull-up for active-low wiring.
|
||||
|
||||
config TQ_RESET_BUTTON_PULLDOWN
|
||||
bool "Enable Wi-Fi reset button pull-down"
|
||||
default n
|
||||
depends on TQ_RESET_BUTTON_ENABLE
|
||||
help
|
||||
Enable the internal pull-down for active-high wiring.
|
||||
|
||||
config TQ_RESET_BUTTON_LONG_PRESS_MS
|
||||
int "Wi-Fi reset button hold duration (ms)"
|
||||
default 5000
|
||||
@@ -699,10 +965,6 @@ menu "TQ Cat Configuration"
|
||||
bool "Swap RGB565 color bytes on bus"
|
||||
default y
|
||||
|
||||
config TQ_SCREEN_BACKLIGHT_ACTIVE_HIGH
|
||||
bool "Backlight active high"
|
||||
default y
|
||||
|
||||
config TQ_SCREEN_BACKLIGHT_BRIGHTNESS_PERCENT
|
||||
int "Default backlight brightness (percent)"
|
||||
default 100
|
||||
@@ -730,56 +992,6 @@ menu "TQ Cat Configuration"
|
||||
default 0
|
||||
range 0 320
|
||||
|
||||
config TQ_SCREEN_RESET_PIN
|
||||
int "Panel reset GPIO (-1 to disable hardware reset)"
|
||||
default 17
|
||||
range -1 48
|
||||
help
|
||||
The 2026-07-24 board maps the ST7789P3 RES signal to IO17.
|
||||
Use -1 only when panel reset is physically not connected.
|
||||
|
||||
config TQ_SCREEN_SPI_MISO_GPIO
|
||||
int "LCD SPI MISO GPIO (-1 to disable)"
|
||||
default -1
|
||||
range -1 48
|
||||
help
|
||||
LCD SPI MISO GPIO. Use -1 when the panel does not connect MISO.
|
||||
|
||||
config TQ_SCREEN_SPI_MOSI_GPIO
|
||||
int "LCD SPI MOSI GPIO"
|
||||
default 18
|
||||
range 0 48
|
||||
help
|
||||
LCD SPI MOSI GPIO.
|
||||
|
||||
config TQ_SCREEN_SPI_CLK_GPIO
|
||||
int "LCD SPI clock GPIO"
|
||||
default 8
|
||||
range 0 48
|
||||
help
|
||||
LCD SPI clock GPIO.
|
||||
|
||||
config TQ_SCREEN_SPI_CS_GPIO
|
||||
int "LCD SPI CS GPIO"
|
||||
default 15
|
||||
range 0 48
|
||||
help
|
||||
LCD SPI chip-select GPIO.
|
||||
|
||||
config TQ_SCREEN_DC_GPIO
|
||||
int "LCD D/C GPIO"
|
||||
default 16
|
||||
range 0 48
|
||||
help
|
||||
LCD data/command GPIO.
|
||||
|
||||
config TQ_SCREEN_BACKLIGHT_GPIO
|
||||
int "LCD backlight GPIO"
|
||||
default 7
|
||||
range 0 48
|
||||
help
|
||||
LCD backlight control GPIO.
|
||||
|
||||
config TQ_SCREEN_SPI_PIXEL_CLOCK_HZ
|
||||
int "LCD SPI pixel clock (Hz)"
|
||||
default 20000000
|
||||
@@ -808,32 +1020,6 @@ menu "TQ Cat Configuration"
|
||||
|
||||
menu "Slot Machine"
|
||||
|
||||
config TQ_SLOT_SWITCH_GPIO
|
||||
int "Slot feature switch GPIO"
|
||||
default 13
|
||||
range 0 48
|
||||
help
|
||||
GPIO used by the input that triggers the slot machine feature.
|
||||
|
||||
config TQ_SLOT_SWITCH_ACTIVE_LEVEL
|
||||
int "Slot feature switch active level"
|
||||
default 0
|
||||
range 0 1
|
||||
help
|
||||
Logic level that means the slot machine feature switch is active.
|
||||
|
||||
config TQ_SLOT_SWITCH_PULLUP
|
||||
bool "Enable slot feature switch pull-up"
|
||||
default y
|
||||
help
|
||||
Enable the internal pull-up for the default active-low slot switch wiring.
|
||||
|
||||
config TQ_SLOT_SWITCH_PULLDOWN
|
||||
bool "Enable slot feature switch pull-down"
|
||||
default n
|
||||
help
|
||||
Leave disabled for the default active-low slot switch wiring.
|
||||
|
||||
config TQ_SLOT_SWITCH_ENABLE
|
||||
bool "Enable slot feature switch worker"
|
||||
default y
|
||||
@@ -859,110 +1045,21 @@ menu "TQ Cat Configuration"
|
||||
The motor searches for the active-low switch and stops after
|
||||
the configured calibration sweep if the switch is not pressed.
|
||||
|
||||
config TQ_STEPPER_IN1_GPIO
|
||||
int "Turntable stepper IN1 GPIO"
|
||||
default 45
|
||||
range 0 48
|
||||
help
|
||||
GPIO connected to the turntable stepper driver IN1 input.
|
||||
|
||||
config TQ_STEPPER_IN2_GPIO
|
||||
int "Turntable stepper IN2 GPIO"
|
||||
default 48
|
||||
range 0 48
|
||||
help
|
||||
GPIO connected to the turntable stepper driver IN2 input.
|
||||
|
||||
config TQ_STEPPER_IN3_GPIO
|
||||
int "Turntable stepper IN3 GPIO"
|
||||
default 47
|
||||
range 0 48
|
||||
help
|
||||
GPIO connected to the turntable stepper driver IN3 input.
|
||||
|
||||
config TQ_STEPPER_IN4_GPIO
|
||||
int "Turntable stepper IN4 GPIO"
|
||||
default 21
|
||||
range 0 48
|
||||
help
|
||||
GPIO connected to the turntable stepper driver IN4 input.
|
||||
|
||||
config TQ_CALIBRATION_SWITCH_GPIO
|
||||
int "Direction calibration switch GPIO"
|
||||
default 12
|
||||
range 0 48
|
||||
help
|
||||
GPIO used for Button 1 on the SW1/IO12 net and for turntable
|
||||
direction calibration.
|
||||
|
||||
config TQ_CALIBRATION_SWITCH_ACTIVE_LEVEL
|
||||
int "Direction calibration switch active level"
|
||||
default 0
|
||||
range 0 1
|
||||
help
|
||||
Logic level that means the calibration switch is active.
|
||||
|
||||
config TQ_CALIBRATION_SWITCH_PULLUP
|
||||
bool "Enable direction calibration switch pull-up"
|
||||
default y
|
||||
help
|
||||
Enable the internal pull-up for the default active-low wiring.
|
||||
|
||||
config TQ_CALIBRATION_SWITCH_PULLDOWN
|
||||
bool "Enable direction calibration switch pull-down"
|
||||
default n
|
||||
help
|
||||
Leave disabled for the default active-low wiring.
|
||||
|
||||
endmenu
|
||||
|
||||
menu "Power & Battery"
|
||||
|
||||
config TQ_POWER_HOLD_GPIO
|
||||
int "Power hold GPIO (-1 to disable)"
|
||||
default -1
|
||||
range -1 48
|
||||
help
|
||||
GPIO used to keep board power enabled after boot. The current
|
||||
battery-sensing board uses IO9 as an ADC input and therefore
|
||||
disables the legacy power-hold output by default.
|
||||
|
||||
config TQ_POWER_HOLD_ACTIVE_LEVEL
|
||||
int "Power hold active level"
|
||||
default 1
|
||||
range 0 1
|
||||
help
|
||||
Logic level that keeps the external power-hold circuit active.
|
||||
|
||||
config TQ_BATTERY_ENABLE
|
||||
bool "Enable battery monitoring"
|
||||
default y
|
||||
|
||||
config TQ_BATTERY_ADC_GPIO
|
||||
int "Battery voltage ADC GPIO"
|
||||
default 9
|
||||
range 0 48
|
||||
depends on TQ_BATTERY_ENABLE
|
||||
|
||||
config TQ_BATTERY_CHARGE_GPIO
|
||||
int "TP4057 charge status GPIO (-1 to disable)"
|
||||
default 10
|
||||
range -1 48
|
||||
depends on TQ_BATTERY_ENABLE
|
||||
|
||||
config TQ_BATTERY_CHARGE_ACTIVE_LEVEL
|
||||
int "TP4057 charging active level"
|
||||
default 0
|
||||
range 0 1
|
||||
depends on TQ_BATTERY_ENABLE
|
||||
|
||||
config TQ_BATTERY_FULL_MIN_VOLTAGE_MV
|
||||
int "Minimum voltage for charge-complete prompt (mV)"
|
||||
default 4150
|
||||
range 4000 4200
|
||||
depends on TQ_BATTERY_ENABLE
|
||||
help
|
||||
The TP4057 status pin cannot distinguish charge termination
|
||||
The charging-status input alone cannot distinguish charge termination
|
||||
from charger removal. Require at least this filtered battery
|
||||
voltage before inferring that charging has completed.
|
||||
|
||||
@@ -1061,12 +1158,6 @@ menu "TQ Cat Configuration"
|
||||
range 3000 4200
|
||||
depends on TQ_BATTERY_CONTROLLED_SHUTDOWN_ENABLE
|
||||
|
||||
config TQ_BATTERY_SHUTDOWN_WAKE_BUTTON_GPIO
|
||||
int "Optional active-low deep-sleep wake button GPIO (-1 to disable)"
|
||||
default -1
|
||||
range -1 48
|
||||
depends on TQ_BATTERY_CONTROLLED_SHUTDOWN_ENABLE
|
||||
|
||||
config TQ_BATTERY_SHUTDOWN_PROMPT_FILE
|
||||
string "Critical-battery shutdown prompt file"
|
||||
default "audio_prompts/shutdown_power_empty.opus"
|
||||
@@ -1383,32 +1474,6 @@ menu "TQ Cat Configuration"
|
||||
Fixed to push2talk. Other upstream modes are intentionally not
|
||||
supported by this firmware runtime.
|
||||
|
||||
config MULTIMODAL_PTT_BUTTON_GPIO
|
||||
int "Push-to-talk button GPIO"
|
||||
default 3
|
||||
range 0 48
|
||||
help
|
||||
GPIO used for the push-to-talk button.
|
||||
|
||||
config MULTIMODAL_PTT_BUTTON_ACTIVE_LEVEL
|
||||
int "Push-to-talk button active level"
|
||||
default 0
|
||||
range 0 1
|
||||
help
|
||||
Logic level that means the push-to-talk button is pressed.
|
||||
|
||||
config MULTIMODAL_PTT_BUTTON_PULLUP
|
||||
bool "Enable push-to-talk button pull-up"
|
||||
default y
|
||||
help
|
||||
Enable the internal pull-up when required by the button wiring.
|
||||
|
||||
config MULTIMODAL_PTT_BUTTON_PULLDOWN
|
||||
bool "Enable push-to-talk button pull-down"
|
||||
default n
|
||||
help
|
||||
Enable the internal pull-down when required by the button wiring.
|
||||
|
||||
config TQ_LOCAL_WAKE_ENABLE
|
||||
bool "Enable local wake-word listener"
|
||||
default y
|
||||
@@ -1832,18 +1897,6 @@ menu "TQ Cat Configuration"
|
||||
range 0 1
|
||||
default 0
|
||||
|
||||
config MULTIMODAL_AUDIO_I2C_SCL_GPIO
|
||||
int "I2C SCL GPIO"
|
||||
default 2
|
||||
help
|
||||
Default from docs/gpio-map.md (ES8311 control SCL on GPIO2).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2C_SDA_GPIO
|
||||
int "I2C SDA GPIO"
|
||||
default 1
|
||||
help
|
||||
Default from docs/gpio-map.md (ES8311 control SDA on GPIO1).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2C_ADDR
|
||||
hex "ES8311 I2C address"
|
||||
default 0x18
|
||||
@@ -1855,46 +1908,10 @@ menu "TQ Cat Configuration"
|
||||
range 0 1
|
||||
default 0
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_MCLK_GPIO
|
||||
int "I2S MCLK GPIO"
|
||||
default 38
|
||||
help
|
||||
Default from docs/gpio-map.md (I2S_MCLK on GPIO38).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_BCLK_GPIO
|
||||
int "I2S BCLK GPIO"
|
||||
default 39
|
||||
help
|
||||
Default from docs/gpio-map.md (I2S_SCLK on GPIO39).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_WS_GPIO
|
||||
int "I2S WS GPIO"
|
||||
default 41
|
||||
help
|
||||
Default from docs/gpio-map.md (I2S_LRCK on GPIO41).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_DOUT_GPIO
|
||||
int "I2S DOUT GPIO"
|
||||
default 40
|
||||
help
|
||||
Default from docs/gpio-map.md (MCU output to ES8311 DSDIN on GPIO40).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_DIN_GPIO
|
||||
int "I2S DIN GPIO"
|
||||
default 42
|
||||
help
|
||||
Default from docs/gpio-map.md (MCU input from ES8311 ASDOUT on GPIO42).
|
||||
|
||||
config MULTIMODAL_AUDIO_USE_MCLK
|
||||
bool "Use external MCLK"
|
||||
default y
|
||||
|
||||
config MULTIMODAL_AUDIO_PA_GPIO
|
||||
int "PA enable GPIO (-1 to disable)"
|
||||
default 11
|
||||
help
|
||||
Default from docs/gpio-map.md (PA_CTRL on IO11).
|
||||
|
||||
config MULTIMODAL_AUDIO_I2S_DMA_DESC_NUM
|
||||
int "I2S DMA descriptor count"
|
||||
default 4
|
||||
|
||||
Reference in New Issue
Block a user